1989 Pacific Seacraft 319m

IJPE : 485.67 sq ft
I : 38.67 ft
J : 14.58 ft
P : 32.50 ft
E : 12.50 ft

The Pacific Seacraft 31 is a new cruising design from the board of renowned naval architect W.I.B. Crealock. She was born of the same wisdom that conceived the immensely successful Crealock 37 and 34. The 31's hull configuration, rig and underbody are very similar to her two forebears, yet she boasts a proportionately broader beam and longer waterline. The result is outstanding speed, comfortable motion, and superb ease of handling. The Pacific Seacraft 31 is designed and built to cross any ocean in comfort and confidence. An impressive bluewater cruiser, she embodies all the Pacific Seacraft trademarks of high quality and fine detail: solid bronze seacocks and portholes, massive anchoring systems, impeccable joiner work, superb engine access and much more. An optional shoal-draft Scheel keel allows sailing in shallow waters without sacrificing deep draft performance The interior of the Pacific Seacraft 31 is fresh, contemporary and versatile. It provides for amazing openness, with lowered bulkheads and ten oversized bronze ports, phenomenal stowage areas, and even an extra-wide bridgedeck that makes it easy to enter the cabin.

Pacific Seacraft 31 Voyagemaker Specifications - Standard Equipment Construction - Hand laminated hull and deck. First hull laminate uses vinylester resin for superior blister resistance. Standard molded-in gel coat color is Antique White. Contrasting boot and sheer stripes. - Stainless steel chainplates and backing plates are caulked and thru-bolted to the hull. Solid teak rubstrake on hull. - Bottom paint includes solvent wash, three layers of epoxy barrier coat and two coats of antifouling bottom paint. - Rudder supported by high strength manganese bronze gudgeon. - Ballast is 4,400 pound (2.0 mt.) solid lead casting with stainless steel keel bolts. Keel to hull joint bedded in epoxy. - Interior is structural fiberglass, plywood & gel coat interior module bonded into hull with fiberglass mat and woven roving. Primary bulkheads bonded into hull & deck w-fiberglass then bolted in place. - Underside of deck, lockers and entire bilge are gel coated to prevent mildew and to facilitate cleaning. - Deck to hull connection: Mating hull & deck flanges bedded in polyurethane adhesive and fastened with stainless steel thru-bolts. - Deck has molded-in nonskid pattern. Deck Equipment - All cleats, winches, turning blocks, pulpits & stanchions have backing plates. Backing plates & hardware caulked with polyurethane. - 30" high stainless steel double rail bow and stern pulpits with running lights and double lifeline stanchions. - Stainless steel stem fitting and bow platform with two anchor rollers, quick-release locking pins and bobstay. - Divided bow chain locker for two anchor rodes. - Deep bulwarks with heavy teak cap rail, hand fitted with butterfly joints. - Chrome plated bronze deck hardware includes: Two Lewmar #44 CST two speed self-tailing genoa sheet winches. Two Lewmar #16 CST self-tailing jib and main halyard winches. Six 7" x 12" and four 4" x 7" opening ports with screens. Two 12" bow mooring cleats with 3" hawse pipes. Two 10" open spring cleats amidships. Two 10" open stern mooring cleats. One anchor deck pipe on foredeck, and one aft. All hinges, hasps, jam cleats, chain pipes, deck fills, etc. - Four teak loop handrails on cabin house. - Large Bomar two way opening hatch. - Designated cleats for each winch. - Two dorades-stainless steel Vetus ventilators with PVC cowls. - Fiberglass seahood, teak companionway sliding hatch and drop boards. - Ball bearing mainsheet traveler mounted on bridge deck in cockpit. - Outboard genoa track with cars. - Stainless steel boarding gates, port and starboard. - Stern chain locker to port with deck pipe and anchor roller. - Stern mounted s.s. swim ladder with teak treads and boarding gate. Interior - White Formica cabin house sides. Hand rubbed teak oil finish. - 6' 2" headroom with teak and holly sole throughout cabin area, all hatches and hatch openings in sole banded in solid teak. - White matte finish below counter height, teak cabinetry above. - Spun polyester wrapped foam cushions with choice of fabrics. - Zippered vinyl headliner for access to deck hardware and wiring. Forward - 6' 6" long and 78" wide double V-berth with shelves on both sides and privacy curtain. - Three teak drawers under V-berth. - Slide out dining table stores beneath V-berth. Main Salon - Teak storage shelf with removable fiddle - both sides. - 6'10" settee berths, port and starboard with storage bins. - Teak navigators table with ice box under lift top. - Tilt out chart storage locker. - Enclosed head with teak shower seat, storage lockers and separate wet hanging locker. - 6' 6" long and 72" wide double berth aft to port. - Hanging locker to starboard. - Two teak loop ceiling handrails. Galley - Gimbaled stainless steel two-burner propane stove w-oven. - Stainless steel safety bar-towel rack. - Large ice box with poured foam insulation, hinged lid and electric ice box pump with overboard discharge. - Polished stainless steel double sink with electric pump pressure fresh water & foot operated manual pump. - Food and dish storage lockers and drawers. Plumbing - Two water tanks with inspection ports, approx. 65 gal. (246 I) total. - Hot and cold pressure fresh water system for galley, head and shower. - Six gallon hot water heater from engine heat exchanger or shore power. - Bronze thru-hull fittings with UL approved bronze seacocks below the waterline, and bronze ball valves above waterline. - All thru hull hose connections are double hose clamped. - Marine head with holding tank and manual overboard pumpout. - Electric shower sump pump with overboard discharge. - Electric automatic bilge pump with switch. - 25 GPM manual bilge pump in cockpit operable by helmsman. Engine - Yanmar 3GM30F, three cylinder, 30 hp diesel with fresh water cooling and 55 amp alternator. Two blade solid bronze propeller. - Clear covered engine control panel in cockpit with tachometer, and engine condition indicators. - Engine hour meter below deck. - Removable 23 gallon (87 l) aluminum fuel tank with gauge and cleaning port [17 gallon (64 l) fuel tank with shoal draft]. - Mechanical fuel pump, electric back-up fuel pump. - Racor fuel filter with water separator. - Seawater strainer bulkhead mounted and water lift muffler system. Electrical - AC-DC master power control panel with AC ammeter, AC voltmeter, polarity test circuit, five AC circuit breakers, DC ammeter, battery condition monitor and nine DC circuit breakers. Panel is hinged for easy access. - Tinned copper wiring throughout. - 110 volt shore power system. - Two marine batteries (approx. 86 amps each). - Four position battery switch. - Four dome lights. - Six reading lights. - One adjustable chart light at navigation station. - Four 110 volt AC duplex receptacles with GFI protection. - RG-8U coaxial antenna cable led from masthead to navigators table. Cockpit - 7' long seats with contoured seat backs and seat drains. - Coamings have two built-in winch handle boxes. - Three cockpit seat lockers for ample storage. - Vented propane storage in starboard coaming locker. - One 2.4 gallon - 10 pound propane tank (empty). - Two safety harness pad eyes. - Contoured helmsman's seat. - Pedestal wheel steering with brake and offset stainless steel pedestal guard, engine throttle controls and emergency tiller. - Two 1-1-2" drains in cockpit sole to seacocks for fast self-bailing. Spars and Rigging - Aluminum spars with two part linear polyurethane paint. - Four sheave masthead, external halyards, airfoil spreaders. - Combination bow - foredeck light on mast. Anchor light on masthead. - Internal conduit with VHF coax cable and wires. - Two single line reefs, reef horns at gooseneck. - Internal 2:1 outhaul, adjustable boom topping lift and cunningham. - 4:1 block and tackle boom vang. - 1-4" - 1x19 s.s. standing rigging. Braided dacron running rigging. - Forged bronze open body turnbuckles. Pacific Seacraft 31 Optional Equipment - Shoal Draft Scheel Keel - Custom Hull Color - Cutter Rig with Single Handers Package (staysail not included) - Max Prop 3 Blade Feathering Propeller - Full Batten Mainsail Upgrade.

The Company offers the details of this vessel in good faith but cannot guarantee or warrant the accuracy of this information nor warrant the condition of the vessel. A buyer should instruct his agents, or his surveyors, to investigate such details as the buyer desires validated. This vessel is offered subject to prior sale, price change, or withdrawal without notice.