1 of 15
Clipper Marine Ltd - Clipper Marine (Poole)
+44 (0)1202 916424
Etap 30 1989
The Etap 30 is regarded as the best yacht Etap produced, she was far ahead of her time in many respects including her easily-driven hull which was designed by Jac de Ridder, it was far and away ahead of most other 30ft cruisers when she was first launched in 1983,she handles delightfully on all points of sail and is still a fairly fast cruiser for her length.
Down below she has five sea-berths, including a quarterberth, and a heads compartment amidships. The galley is spacious and useable.
This Etap 30 is on her berth here in Poole and is ready for viewing, for any further information or to arrange a viewing please contact Clipper Marine Poole on 01202 916424 or email email@example.com
Single piece GRP moulded hull.
GRP sandwich laminate construction with foam core.
Moulded internal structural matrix and headlining.
Plywood bulkheads located in internal moulded matrix.
Bolt-on iron ballast keel with stainless steel keel bolts.
Blue gelcoat finish to hull, cream gelcoat to decks
Hull below waterline treated with Copper coat anti-foul.
Single piece GRP moulded deck with integrated self-draining cockpit.
Deck finished in cream coloured gelcoat.
Full bonded Perspex portlights.
Perspex contoured deck hatches.
Moulded non-slip finished to coach roof.
Non-slip panel finish to side decks and foredeck.
Teak laid panels on plywood cockpit locker hatches port and starboard.
SPARS AND RIGGING
Deck stepped, single spreader anodised alloy mast.
Anodised alloy boom with single line reefing.
All standing rigging of 1x19 stainless steel.
Roller reefing system fitted on forestay for Genoa.
Block and tackle adjustable back stay.
All lines lead aft to cockpit.
Spinlock rope clutches.
Genoa track and car system, control lines lead aft to cockpit.
Easy Block double purchase mainsheet system with adjustable track and car.
Primary Winches – 2x Lewmar 16, two-speed.
Secondary Winches – 2x Lewmar 16, two-speed.
Mainsail – Lucas 7/8 fractional Rig reefing x 3
Genoa – White Dacron, Roller reefing.
Tubular anodised alloy pulpit and pushpit rails.
Deck mounted alloy stanchions supporting stainless steel guard wires, guard wire gate on transom between pushpit railings.
Etap style tubular anodised alloy toerail rubbing the length of the deck edge.
Stainless steel double stemhead roller.
Tubular anodised alloy cleats forward, midships and aft.
Opening deck hatch providing access to anchor locker aft of windlass.
Deck stepped mast with all lines lead aft to cockpit on port and starboard sides.
Genoa track and car mounted on inboard edge of side deck with control lines lead aft to cockpit.
Banks of Spinlock rope clutches on port and starboard sided of companionway.
Halyard winches mounted port and starboard sides of companionway.
Moulded cockpit coamings with primary winches mounted outboard.
Bench seating on port and starboard sides of cockpit with seating across transom, aft of tiller.
Large cockpit locker below port cockpit seat with twin lids for access fore and aft.
Self-draining gas locker beneath seating, aft to starboard.
Lifting sole panel provides access to gearbox and fuel tank.
Tek Dek perma teak to decks.
Teak decking to cockpit.
Volvo Penta 18hp marine diesel.
2 cylinder, naturally aspirated, directly cooled.
Volvo Penta sail drive.
Engine serviced May 2019.
Stainless steel diesel tank.
Primary fuel filter with water separator.
2 x batteries
Below deck the Etap has a distinctive modern finish. The interior joinery work being built of sappelle veneered marine plywood with stainless steel and alloy fittings and trims. A GRP moulding finishes the headlining throughout the interior. Soleboards are of the traditional teak and holly veneered plywood, all lifting to provide full access to the bilge.
Accessed through the heads compartment. Two single berths in the traditional V-berth configuration. Infill section to create large double bunk when required. Shelves running the length of the bunk overhead, outboard, port and starboard. Lined bin type lockers beneath bunks aft. Opening Perspex deck hatch to provide light and ventilation.
Compartment spanning full width of the boat immediately aft of forepeak. Jabsco manual marine toilet to starboard, inboard facing. Wash hand basin and vanity unit outboard to port. A hanging and shelved locker is provided outboard of the heads.
Centrally located, double dropleaf table. Bench settee on port side, converting to single bunk when required. L-shaped settee to starboard, converting to compact double. Storage lockers provided behind seat backs with shelves outboard of seating. Overhead lockers provided outboard port and starboard, running the length of the settees, upholstery re- upholstered 1 year ago
U-shaped galley. Gimbal mounted Nelson gas cooker fitted 2017. Stainless steel sink forward with top loading fridge outboard of sink. Selection of lockers provided outboard of worktop and below sink unit.
CHART TABLE AND QUARTER BERTH
Forward facing chart table with navigator using forward section of quarter berth as a seat. Chart storage provided within table, selection of drawers beneath. Ships switch panel and navigation instruments mounted outboard. Quarter berth extending aft from chart table along starboard side.
Depth – Nasa Clipper
Log – depth and Speed Nasa Clipper
Plotter – Garmin 415 (mounted at chart table)
Raymarine - AutoPilot
Navtex – Target Navtex Pro Plus
VHF – Silva S15 VHF
Hot water Calorifier (new)
Rutland Wind generator
Nikkai 600W inverter
Anchor x 2 with galvanised chain
Fire extinguisher (saloon)